模具述语
一、入水：gate
进入位： gate location
水口形式：gate type
大水口：edge gate
细水口： pin-point gate
水口大小：gate size
转水口： switching runner/gate
唧嘴口径： sprue diameter
二、流道: runner
热流道： hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道：round(full/half runner
流道电脑分析：mold flow analysis
流道平衡:runner balance
热嘴： hot sprue
热流道板：hot manifold
发热管：cartridge heater
探针: thermocouples
插头： connector plug
插座： connector socket
密封/封料： seal
三、运水：water line
喉塞：line lpug
喉管：tube
塑胶管：plastic tube
快速接头：jiffy quick connector plug/socker
四、模具零件： mold components
三板模：3-plate mold
二板模：2-plate mold
边钉/导边：leader pin/guide pin
边司/导套：bushing/guide bushing
中托司：shoulder guide bushing
中托边L：guide pin
顶针板：ejector retainner plate
托板： support plate
螺丝： screw
管钉：dowel pin
开模槽：ply bar scot
内模管位：core/cavity inter-lock
顶针： ejector pin
司筒：ejector sleeve
司筒针：ejector pin
推板：stripper plate
缩呵：movable core,return core core puller
扣机（尼龙拉勾）：nylon latch lock
斜顶：lifter
模胚（架）： mold base
上内模：cavity insert
下内模：core insert
行位（滑块）： slide
镶件：insert
压座/斜鸡：wedge
耐磨板/油板：wedge wear plate
压条：plate
撑头: support pillar
唧嘴： sprue bushing
挡板：stop plate
定位圈：locating ring
锁扣：latch
扣鸡：parting lock set
推杆：push bar
栓打螺丝：S.H.S.B
顶板：eracuretun
活动臂：lever arm
分流锥：spure sperader
水口司:bush
垃圾钉：stop pin
隔片：buffle
弹弓柱：spring rod
弹弓:die spring
中托司：ejector guide bush
中托边：ejector guide pin
镶针：pin
销子：dowel pin
波子弹弓：ball catch
喉塞: pipe plug
锁模块：lock plate
斜顶：angle from pin
斜顶杆：angle ejector rod
尼龙拉勾：parting locks
活动臂：lever arm
复位键、提前回杆：early return bar
气阀：valves
斜导边：angle pin
术语：terms
承压平面平衡：parting surface support balance
模排气：parting line venting
回针碰料位：return pin and cavity interference
模总高超出啤机规格：mold base shut hight
顶针碰运水：water line interferes withejector pin
料位出上/下模：part from cavith (core) side
模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件： Do not use (core/cavity) insert
用铍铜做镶件： use beryllium copper insert
初步（正式）模图设计：preliinary (final) mold design
反呵：reverse core
弹弓压缩量：spring compressed length
稳定性好：good stability,stable
强度不够：insufficient rigidity
均匀冷却：even cooling
扣模：sticking
热膨胀：thero expansion
公差：tolorance
铜公(电极）：copper electrode
